156-315.81 Exam Dumps - Check Point Certified Security Expert R81.20

 SecureXL is a technology that accelerates the performance of the Check Point Security Gateway by offloading CPU-intensive operations from the Firewall kernel to the SecureXL device. SecureXL can handle various types of traffic, such as TCP, UDP, ICMP, non-IP, VPN, NAT, etc. SecureXL can also work with various features, such as CoreXL, ClusterXL, QoS, etc.

One way to indicate that SecureXL is enabled is to use the fwaccel commands in clish. Clish is a command-line shell that provides a user-friendly interface for configuring and managing Check Point products. The fwaccel commands are used to control and monitor SecureXL operations, such as enabling or disabling SecureXL, viewing SecureXL statistics, managing SecureXL templates, etc. For example, the command fwaccel stat shows the status of SecureXL, such as whether it is on or off, how many packets are accelerated or not accelerated, etc.

The other options are not valid indicators of SecureXL being enabled:

• A. Dynamic objects are available in the Object Explorer: Dynamic objects are objects that represent IP addresses that change over time, such as VPN clients, DHCP clients, etc. Dynamic objects are available in the Object Explorer regardless of whether SecureXL is enabled or not.
• B. SecureXL can be disabled in cpconfig: Cpconfig is a command-line tool that allows you to configure various settings of Check Point products, such as administrator password, GUI clients, SNMP extension, etc. SecureXL can be disabled in cpconfig only if it was enabled before. Therefore, this option does not indicate that SecureXL is enabled.
• D. Only one packet in a stream is seen in a fw monitor packet capture: Fw monitor is a command-line tool that allows you to capture and analyze network traffic passing through the Security Gateway. Fw monitor shows the traffic at different inspection points in the Firewall kernel. If SecureXL is enabled, some packets may be accelerated by SecureXL and bypass the Firewall kernel inspection. Therefore, fw monitor may not see all packets in a stream. However, this does not mean that only one packet in a stream will be seen by fw monitor. Some packets may still go through the Firewall kernel inspection and be seen by fw monitor. Therefore, this option does not indicate that SecureXL is enabled.

Therefore, the correct answer is C.

References: How to enable/disable Check Point SecureXL via CLI, Part 3 - SecureXL, What is SecureXL?, Clish - Command Line Interface Shell, sk30583: What is FW Monitor?

The API command to create a new host with the name "New Host" and IP address "192.168.0.10" is:

This command adds a host object with the specified name and IP address to the Check Point configuration.

References: Check Point documentation or training materials related to API commands.

Hybrid Emulation Mode is a mode of operation that allows load sharing of emulation between an on premise appliance and the cloud. Emulation is a process that analyzes files for malicious behavior by running them in a virtual sandbox. Hybrid Emulation Mode enables you to optimize the performance and scalability of your Threat Emulation solution by distributing the emulation workload between your local SandBlast appliance and the Check Point cloud service. References: Check Point Security Expert R81 Course, Threat Emulation Administration Guide

The blades of Threat Prevention in Check Point include:

Intrusion Prevention System (IPS)

AntiVirus

AntiBot

SandBlast Threat Emulation/Extraction

So, the correct answer is D, which includes all the mentioned blades.

References: Check Point Certified Security Expert (CCSE) R81 documentation and learning resources.

The command used to display status information for various components is show sysenv all. This command provides comprehensive status information about the system's environment and various components, including hardware and software components. It can be useful for troubleshooting and monitoring the system's health.

References: Check Point Certified Security Expert (CCSE) R81 documentation and learning resources.:

 The main stages of a policy installation are Verification & Compilation, Transfer and Commit. Verification & Compilation is the stage where the Security Management Server checks the validity and consistency of the policy and compiles it into a binary format. Transfer is the stage where the compiled policy is sent to the Security Gateways over a secure channel. Commit is the stage where the Security Gateways activate the new policy and update their connections table accordingly. References: Check Point Security Expert R81 Course, Policy Installation Process

Mobile Access encrypts all traffic using HTTPS for web-based applications and 3DES or RC4 algorithm for native applications. For end users to access the native applications, they need to install the SSL Network Extender, which is a lightweight VPN client that creates a secure SSL tunnel to the Mobile Access gateway. The SSL Network Extender supports various types of native applications, such as email clients, file sharing, and remote desktop. References: Mobile Access Administration Guide, SSL Network Extender

 To add the company logo to reports, you would save the logo as a PNG file with the name ‘cover-company-logo.png’ and then copy that image file to the $RTDIR/smartview/conf directory on the SmartEvent server. The $RTDIR is an environment variable that points to the runtime directory of the SmartEvent server, which is usually /opt/CPrt-R81. The smartview/conf directory contains the configuration files for SmartView, which is a web-based interface for viewing reports and dashboards generated by SmartEvent. References: SmartEvent Administration Guide, SK120193 - How to add a company logo to SmartView reports