CFPS Exam Dumps - Certified Fire Protection Specialist (CFPS)

The maximum discharge time permitted for halocarbon clean agent systems is10 seconds. This is the requirement of NFPA 2001, which is the standard for clean agent fire extinguishing systems.NFPA 2001 states that the discharge time for halocarbon agents shall not exceed 10 seconds, unless otherwise permitted by the authority having jurisdiction1. Halocarbon agents are synthetic compounds that contain carbon, fluorine, and sometimes other elements, such as hydrogen, chlorine, or bromine.Examples of halocarbon agents include HFC-227ea, HFC-125, and FK-5-1-122. Halocarbon agents work by absorbing heat and interrupting the chemical chain reaction of the fire.They are electrically nonconductive and leave no residue upon evaporation3.Halocarbon agents are suitable for protecting Class A, B, and C fires involving electrical equipment, flammable liquids, and ordinary combustibles4. The discharge time is the time required to release the agent from the storage containers to the protected enclosure.A short discharge time is important to achieve the design concentration of the agent before the fire grows or spreads5.References:

• NFPA 2001: Standard on Clean Agent Fire Extinguishing Systems
• Clean Agent System Basics | NFPA
• Fire Fighting Foams - Chemguard
• Clean Agent Fire Suppression Systems | Fike
• Category | Rotarex Firetec

According to the web search results, the goals of the first edition of NFPA 13D were to provide sufficient time for safe egress or rescue, economic viability, and limit damage to the dwelling. The first edition of NFPA 13D was published in 1975 and was based on the concept of a “life safety” sprinkler system that was intended to protect the occupants of one- and two-family dwellings and manufactured homes from fire.The first edition of NFPA 13D stated that the system was not designed to protect the property or contents from fire damage, but rather to provide a tenable environment for escape or rescue1.The first edition of NFPA 13D also recognized the need for economic viability of the system, and therefore allowed for reduced water supply and piping requirements compared to other sprinkler standards2.The first edition of NFPA 13D did not explicitly state the goal of limiting damage to the dwelling, but it implied that the system would have some beneficial effect on the fire spread and severity by stating that the system was designed to prevent flashover in the room of fire origin1.References:

• NFPA 13D: Standard for the Installation of Sprinkler Systems in One- and Two-Family Dwellings and Manufactured Homes, 1975 Edition, Section 1-11
• Fire Protection Handbook, 20th Edition, Volume 1, Chapter 8, Section 8.2.1.22

Spontaneous combustion is the exception to the requirement of a combustible material, an oxidizing agent, and an ignition source for combustion to take place. Spontaneous combustion is a phenomenon in which a material can ignite without any external heat or flame, due to a chemical reaction within the material that generates enough heat to reach the ignition temperature. Spontaneous combustion can occur in certain materials that are prone to self-heating, such as oily rags, hay, coal, and compost. Spontaneous combustion is a type of smoldering combustion, which is a slow, low-temperature, flameless form of combustion.References:

• Fire Protection Handbook, 20th Edition, Volume 1, Chapter 2, Section 2.2.1.11
• NFPA 921: Guide for Fire and Explosion Investigations, 2021 Edition, Section 4.3.12

Fire alarm visible appliance source intensity is measured in candela, which is the unit of luminous intensity in a given direction. Candela is defined as the amount of light emitted by a single candle in a specific direction. The intensity of a strobe light depends on the candela rating, the flash rate, and the flash duration. The higher the candela rating, the brighter the light. The National Fire Protection Association (NFPA) and the Americans with Disabilities Act (ADA) have established minimum and maximum candela ratings for fire alarm visible appliances in different locations and applications.References:Strobe Light Requirements: Proper location of visible notification …;Handbook of Visual Notification Appliances for Fire Alarm Applications;Audible Visible Appliance Reference Guide - Fire - studylib.net

Potassium bicarbonate is a dry chemical agent that is considered to be twice as effective as sodium bicarbonate in fire suppression, especially for Class B fires involving flammable liquids and gases. This is because potassium bicarbonate has a higher melting point and a lower decomposition temperature than sodium bicarbonate, which allows it to form a more stable and insulating layer on the burning surface.Potassium bicarbonate also has a lower pH and a higher specific gravity than sodium bicarbonate, which enhances its penetration and dispersion abilities123.References:Dry Chemical Agents - Purple-K Powder is Purple - Chemguard;Evaluation of Dry Chemical Fire Extinguishing Standards - NFPA;Potassium bicarbonate - Wikipedia.