CWAP-404 Exam Dumps - Certified Wireless Analysis Professional

A STA that supports 802.11k Radio Measurement would send a Neighbor Request to an AP to request a list of neighboring APs which the STA can use as roaming candidates. A Neighbor Request is an Action frame that contains a subelement specifying the type of information that the STA wants to receive from the AP. A Neighbor Report is an Action frame that contains a subelement with a list of neighboring APs that match the criteria specified in the Neighbor Request. The Neighbor Report provides information such as BSSID, channel, operating class, and PHY type of each neighboring AP. This information helps the STA to perform intelligent roaming decisions based on signal quality, load, and compatibility . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 434; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 435.

A PS-Poll (Power Save Poll) frame is not an 802.11 management frame. A PS-Poll frame is a type of control frame that is used by a STA in power save mode to request data frames from an AP. A STA in power save mode can conserve battery power by periodically sleeping and waking up. When a STA sleeps, it cannot receive any data frames from the AP, so it informs the AP of its power save status by setting a bit in its MAC header. The AP then buffers any data frames destined for the sleeping STA until it wakes up. When a STA wakes up, it sends a PS-Poll frame to the AP, indicating its association ID and requesting any buffered data frames. The AP thenresponds with one or more data frames, followed by an ACK or BA frame from the STA. The other options are not correct, as they are types of 802.11 management frames. An Action frame is used to perform various management actions, such as spectrum management, QoS management, radio measurement, etc. A Beacon frame is used to advertise the presence and capabilities of an AP or BSS. An Authentication frame is used to establish or terminate an authentication relationship between a STA and an AP. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 6: 802.11 Frame Exchanges, page 169-170

The HT protection mode in which an AP is operating can be identified by looking at the HT Operations element in a Beacon frame. The HT Operations element is a part of the Beacon frame that contains information about the High Throughput (HT) capabilities and operation of an 802.11n BSS. The HT Operations element has a field called HT Protection, which indicates how the BSS protects its HT transmissions from interference or collisions with non-HT devices or BSSs. The HT Protection field can have four values: No Protection, Nonmember Protection, 20 MHz Protection, or Non-HT Mixed Mode. The other options are not correct, as they do not contain information about the HT protection mode. The HT Protection element does not exist, the ERP Information element is used for Extended Rate PHY (ERP) protection mode for 802.11g devices, and the HT Capabilities element is used for indicating the supported HT features of an individual device. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 125-126

A Reassociation Request frame is sent every time a STA roams from one AP to another within the same ESS. A Reassociation Request frame is similar to an Association Request frame, but it also contains the BSSID of the current AP that the STA is leaving. This allows the new AP to coordinate with the old AP and transfer the STA’s context information, such as security keys, QoS parameters, and buffered frames. This way, the STA can maintain its connectivity and session continuity during roaming . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 195;CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 196.

The default 802.11 authentication method for a STA when using Pre-RSNA is Open System. This is the simplest and most common authentication method, which does not provide any security or encryption. In Open System authentication, the STA sends an Authentication Request frame to the AP, and the AP responds with an Authentication Response frame with a status code of success. After this, the STA can proceed to association with the AP . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 181; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 183.

A capture visualization tool is a software application that can open a packet capture file and display various graphs, charts, tables, and statistics that illustrate the characteristics and behavior of the wireless network. A capture visualization tool can help a network administrator with little knowledge of 802.11 protocols to evaluate the overall health and performance of their wireless network by providing a visual and intuitive representation of the captured data. A spectrum analyzer is a hardware device that measures the radio frequency signals in a given frequency range and displays their amplitude, frequency, and modulation. A spectrum analyzer can help identify sources of interference and noise in the wireless environment, but it cannot open a packet capture file. Python is a programming language that can be used to write scripts or applications that manipulate or analyze packet capture files, but it requires coding skills and knowledge of 802.11 protocols. A WLAN scanner is a software application that scans for available wireless networks and displays information such as SSID, BSSID, channel, signal strength, security type, and vendor. A WLAN scanner can help discover wireless networks and their basic parameters, but it cannot open a packet capture file345 References:

• CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 63
• CWAP-404 Objectives, Section 2.5: Use capture visualization tools
• CWAP-404 Study Guide, Chapter 4: Spectrum Analysis and Troubleshooting, page 117
• CWAP-404 Objectives, Section 4.1: Use spectrum analysis tools
• CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 33
• CWAP-404 Objectives, Section 2.2: Analyze field values

The 4-way handshake is the process that establishes the pairwise transient key (PTK) between the client and the AP in WPA2-PSK. The PTK is derived from the PSK, the SSID, and some random numbers exchanged in the handshake frames. The PTK is used to encrypt and decrypt the data frames between the client and the AP. Therefore, in order to decrypt WPA2-PSK data packets, a protocol analyzer needs to capture the 4-way handshake frames and have the PSK and SSID configured in the analyzer software12 References:

• CWAP-404 Study Guide, Chapter 3: 802.11 MAC Layer Frame Formats and Technologies, page 87
• CWAP-404 Objectives, Section 3.5: Analyze security exchanges

The most likely cause of higher airtime utilization on the first 20 MHz of the 80 MHz channel is non-Wi-Fi interference. Non-Wi-Fi interference can prevent an AP from using its full channel width, as it will degrade the signal quality and increase the noise floor on some parts of the channel. This will force the AP to fall back to a narrower channel width, such as 20 MHz or 40 MHz, to maintain communication with its clients. The waterfall plot can help identify non-Wi-Fi interference by showing spikes or bursts of RF energy on specific frequencies or sub-channels. The other options are not correct, as they do not explain why only the first 20 MHz of the channel has higher airtime utilization. References: [Wireless Analysis Professional Study Guide], Chapter 3: Spectrum Analysis, page 74-75