220-1101 Exam Dumps - CompTIA A+ Certification Exam: Core 1

Automatic document feeder (ADF) is a feature that allows a multifunction printer to photocopy documents with hundreds of pages automatically without requiring manual intervention. ADF scans multiple pages from a stack of documents and feeds them into the printer one by one. SMB is a network protocol that allows file sharing and printer access among different devices on a network. PCL is a printer language that controls how data is formatted for printing. SSH is a network protocol that allows secure remote access to another device over an encrypted connection.

A patch panel is a mounted hardware unit containing ports used to manage cable connections. The individual pairs of a Cat 6 cable are terminated on the patch panel, which then provides a central location for cable management and organization. The patch panel is then connected to the switch using a patch cable.

Loading the hard disk drive (HDD) drivers using a flash drive is the most likely action that can fix the issue of a computer not being able to find the hard drive during an OS installation from Windows 7 to Windows 10. The HDD may have a different interface or controller than what Windows 10 supports by default, such as SATA or RAID, which would require loading additional drivers during the installation process. The technician can use a flash drive to load the drivers from another device or source. Changing the partition to MBR, upgrading the RAM modules, or replacing the hard drive are not likely to fix the issue, as they are not related to the HDD drivers

The user should check the display settings on the computer and set them to extend/duplicate. This will allow the computer to send the video signal to both the laptop screen and the projector. If the display settings are set to only show on one screen, then the projector may not detect any source. According to the CompTIA Core1 objectives, one of the common display issues is no image on screen. A troubleshooting guide for projectors also suggests checking the display settings as a possible solution for no source found error.

The administrator should use RAID 0 for a video-rendering workstation at minimal cost. RAID 0, also known as striping, is a RAID configuration that splits data evenly across two or more disks, without parity information, redundancy, or fault tolerance. RAID 0 has the following advantages and disadvantages:

High read/write performance: RAID 0 can increase the data transfer rate by using multiple disks in parallel. This can improve the speed and efficiency of video rendering, which involves processing large amounts of data. RAID 0 can also reduce the latency and seek time of the disks, as the data is distributed across multiple spindles.

Maximum drive storage utilization: RAID 0 can use the full capacity of the disks, without wasting any space for parity or mirroring. This can lower the cost and increase the storage space for the workstation. For example, if two 500 GB disks are used in RAID 0, the total capacity of the array will be 1000 GB.

No redundancy or fault tolerance: RAID 0 does not provide any protection against data loss or disk failure. If one disk fails, the entire array will fail and the data will be unrecoverable. Therefore, RAID 0 should only be used for non-critical data that is backed up elsewhere, or for temporary files that can be recreated.

The most likely component that is failing and causing the PC to overheat is D. CPU fan. The CPU fan is a vital part of the cooling system that prevents the CPU from overheating by blowing air over the heatsink and dissipating the heat. If the CPU fan is faulty, noisy, or clogged with dust, it can reduce the airflow and cause the CPU temperature to rise12. This can result in poor performance, instability, or shutdowns of the PC.

The other components are less likely to be the cause of overheating. RAM, motherboard, and SSD do not generate as much heat as the CPU and usually do not require fans to cool them down1. They may overheat if there is poor ventilation in the case or if they are defective, but they are not as common as a failing CPU fan.

Therefore, the correct answer is D. CPU fan. This is the most likely component that is failing and causing the PC to overheat.

DHCP (Dynamic Host Configuration Protocol) is a network service that automatically assigns IP addresses and other configuration parameters to devices that request them. DHCP simplifies the management of IP addresses and avoids conflicts and errors67. An APIPA (Automatic Private IP Addressing) is a feature of Windows that assigns a default IP address in the range of 169.254.x.x to a device when it cannot obtain a valid IP address from a DHCP server. An APIPA indicates that there is a problem with the DHCP service or the network connectivity between the device and the DHCP server89. Therefore, the technician should investigate the DHCP service first to check if it is running, configured correctly, and has enough available IP addresses to assign. The other services are not directly related to the IP address assignment. RADIUS (Remote Authentication Dial-In User Service) is a protocol that provides centralized authentication, authorization, and accounting for network access10. AAA (Authentication, Authorization, and Accounting) is a framework that controls the access and usage of network resources11. DNS (Domain Name System) is a service that resolves domain names into IP addresses12.

References

6: What is DHCP (Dynamic Host Configuration Protocol)? - Definition from WhatIs.com

7: How DHCP works - Windows Server | Microsoft Docs

8: What is APIPA (Automatic Private IP Addressing)? - Definition from WhatIs.com

9: How to Fix an IP Address Conflict

10: What is RADIUS (Remote Authentication Dial-In User Service)? - Definition from WhatIs.com

11: What is AAA (authentication, authorization, and accounting)? - Definition from WhatIs.com

12: What is DNS (Domain Name System)? - Definition from WhatIs.com

A patch panel is a mounted hardware unit containing ports used to manage cable connections. The individual pairs of a Cat 6 cable are terminated on the patch panel, which then provides a central location for cable management and organization. The patch panel is then connected to the switch using a patch cable.