Black Friday Special Sale Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: scxmas70

HPE0-S59 Exam Dumps - HPE Compute Solutions

Question # 4

Your customer plans to add four HPE Synergy frames to an existing management ring Ail installed frames are equipped with two 2-port FLM modules, while new frames will be equipped with 4-port FLM modules.

Which statement about mixing different FLM modules is true?

A.

Existing 2-port FLM modules must be replaced with 4-port FLM modules

B.

A management ring can contain mixed frame link module configurations

C.

A management ring with mixed FLM modules cannot have more than 12 frames

D.

Mixing different FLM modules is allowed if all of them have the same firmware version

Full Access
Question # 5

You modified a logical interconnect group mat is used to configure logical interconnects in five different logical enclosures. What will be the impact of that change?

A.

All physical interconnects from affected logical interconnects will be placed in a maintenance mode

B.

All physical interconnects from the affected logical interconnects must he rebooted to activate the new configuration

C.

All logical interconnects configured using this logical Interconnect group will report inconsistency

D.

All logical interconnects configured using this logical interconnect group will be automatically updated

Full Access
Question # 6

Match each HPE OneView network type with its definition.

Full Access
Question # 7

When should Private Network be enabled?

A.

When a customer needs the ability to create a network dedicated to a single compute node.

B.

When a customer needs additional network security by limiting traffic flow for the given network.

C.

When a customer needs a heartbeat network between two compute nodes for building a cluster.

D.

When a customer needs each port associated with a given uplink set to be 100Gb/s.

Full Access
Question # 8

The proposal consists of.

- 3 HPE Synergy 12000 frames

- 6 HPE Composer 2 modules

- 2 HPE Virtual Connect SE 100 GO F32 Module

- 4 HPE Synergy 50 GO interconnect Link Module

Which statements about this proposed design are true? (Select two.)

A.

The selected interconnect modules do not provide the requested WWN virtualization

B.

HPE Synergy 50Gb ILMs must be replaced with HPE Virtual Connect SE 100 GO F32 modules

C.

The current setup can support up to 18 HPE Synergy 480 Gen10 Plus compute modules

D.

FC upgrade licenses for HPE Virtual Connect SE 100 GbF32 Module must be added

E.

Remove 4 HPE Composer 2 modules from the design, as they are not required

Full Access
Question # 9

Refer to the exhibit.

Which statement about this logical interconnect group is true?

A.

The master modules are located in the interconnect bays 2 and 5

B.

For the given downlink speed, the maximum number of frames is reached

C.

Both master modules are located in the same HPE Synergy frame

D.

To use interconnect bay set 3, all compute nodes must be half-height

Full Access
Question # 10

Your customer plans to deploy VMware vSAN using D3940 Storage Modules.

Which statement about this solution is true?

A.

The 12Gb SAS modules required for D3940 connectivity can only be installed in the first fabric.

B.

To use the storage controller that will access D3940 storage modules, a second CPU must be installed.

C.

For VMware vSAN deployment, all drives in the D3940 storage modules must be SSD drives.

D.

All drives in the D3940 storage modules must formulate a single logical drive with RAID5 configured

Full Access
Question # 11

Which statement about port flap protection is true?

A.

It can disable link aggregation groups or stacking ports that have gone down and come up in quick succession.

B.

It allows an administrator to suppress excessive inbound multicast, broadcast, and DLF packets.

C.

It allows configuration of hardware Layer 2 switching behavior of multicast traffic to optimize network resource usage.

D.

It allows the creation of LACP groups on the upstream switch that span multiple HPE Synergy Virtual Connect modules.

Full Access
Question # 12

One of the administrators added some connections within a server profile that was created using a template. This server profile did not report inconsistency.

What is the most likely reason for this behavior?

A.

The administrator removed FC connections that are not monitored by default.

B.

Connections defined in the server profile are not monitored for compliance.

C.

Consistency check for connections is set to Minimum or Not checked.

D.

The server is in maintenance mode and does not report any issues.

Full Access
Question # 13

Your customer is trying to grow a VMware cluster using HPE OneView for VMware vCenter Server. They get an error and cannot proceed.

Which tool should you use to troubleshoot the problem?

A.

HPE OneView interface to import an existing cluster using the hypervisor cluster profile functionality.

B.

HPE OneView for VMware vCenter Server to verify if the server profile template is properly imported and registered.

C.

vCenter Server to use the HPE OneView for VMware vCenter plugin to import the cluster for HPE OneView management.

D.

iLO interface of a given HPE Synergy compute node to verify whether this node is registered within HPE OneView.

Full Access
Question # 14

Your customer plans to deploy VMware ESXi 7.0 U2, and they are looking for a hardware platform that will allow them to use up to 24 TB of physical memory.

Which HPE compute system meets the customer's requirements?

A.

HPE Superdome Flex

B.

HPE ProLiant DL380 Gen 10 Plus

C.

HPE ProLiant DL580 Gen 10

D.

HPE Synergy 480 Gen10 Plus

Full Access
Question # 15

Your customer plans to deploy HPE Superdome Flex and configure two nPars, each based on two chassis Which components must be included in the proposal to meet the customer’s needs?

A.

Rack Management Controller for nPar management

B.

HPE Superdome Flex Grid licenses enabling connectivity between chassis

C.

At least Tour HPE Persistent Memory DIMMs per nPar

D.

One base chassis and three expansion chassis with licenses

Full Access
Question # 16

Which statement about HPE Apollo 2000 Gen10 Plus platform is true?

A.

It is equipped with HPE Persistent memory by default

B.

It can support a single processor only and up to 4 per chassis

C.

It is fully managed using HPE OneView including all connections

D.

It offers servers with AMD EPYC and Intel Xeon Scalable CPUs

Full Access
Question # 17

How will traffic for a given network be affected if the purpose is changed from General to VM Migration?

A.

Changing this parameter to VM Migration will give higher priority for vMotion traffic.

B.

Changing this parameter does not affect the behavior of the network or traffic.

C.

If VM Migration is selected, all types of traffic other than vMotion will be blocked.

D.

This parameter will allow an administrator to define a VMkernel port.

Full Access
Question # 18

Your customer plans to manage HPE Primera using HPE Oneview

Which storage management tasks can be completed using HPE OneView for this environment?

A.

CPG management

B.

Volume provisioning

C.

Cache management

D.

Replication setup

Full Access
Question # 19

An administrator tries to open iLO interlace from HPE OneView Instead of being automatically logged in a login prompt displays

Where should you start the troubleshooting process?

A.

At the iLO interface to verify whether the ILO Advanced license is properly applied

B.

At HPE OneView Interface to verify whether the server is In the maintenance mode

C.

At the iLO interface to verify whether the SSO certificate is removed from an iLO.

D.

At HPE OneView Interface to verify whether the iLO processor is disabled

Full Access
Question # 20

Your customer reports that they cannot deploy HPE Synergy compute nodes using HPE OneView for VMware vCenter Server (HPE OV4VC).

What should you check during troubleshooting process?

A.

If HPE OneView credentials are added in vCenter Server

B.

If an compute nodes are added to the vCenter Server

C.

If the HPE Oneview instance Is integrated with HPE OV4VC.

D.

If vCenter Server is licensed in the HPE Oneview interface

Full Access
Question # 21

Your customer has an HPE Synergy frame equipped with a D3940 Storage Module. Each of the compute nodes has an appropriate storage controller Installed and two 12Gb SAS switches installed in the first fabric.

The customer reports that compute nodes cannot access the storage module. What should you verify first when troubleshooting this problem?

A.

If the D3940 module is imported in managed state that allows volume provisioning.

B.

If there Is a logical interconnect created based on the 12Gb SAS switches.

C.

If the D3940 storage module is property licensed through HPE OneView interface.

D.

If there is at least one ISCSI network configured that will provide access to the module.

Full Access
Question # 22

You need to configure a RoCE network to enable lossless networking for HPE J2000 Flash Enclosure support Which interconnects are required to support this connection? (Select two.)

A.

HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy

B.

HPE Virtual Connect SE 16Gb FC Module for HPE Synergy

C.

HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy

D.

HPE Virtual Connect SE 32Gb FC Module for HPE Synergy

E.

Brocade 16Gb Fibfe Channel SAN Switch Module for HPE Synergy

F.

Brocade 32Gb Fibre Channel SAN Switch Module for HPE Synergy

Full Access
Question # 23

Match HPE Superdome Flex system with its specific feature.

Full Access
Question # 24

Click the drop-down menu that will allow you to define the location of the master modules within the logical interconnect group.

Full Access
Question # 25

Your customer wants to compare HPE Superdome Flex with HPE Superdome Flex 280.

Which statement about these two systems is true?

A.

HPE Superdome Flex must be in memory mode to support HPE Persistent Memory.

B.

HPE Superdome Flex 280 can be managed using iLO5 management processor.

C.

HPE Superdome Flex requires Rack Management Controller to support multiple nPars.

D.

HPE Superdome Flex 280 can scale up to 16 sockets and 24TB of memory.

Full Access
Question # 26

An HPE Synergy customer needs to prevent a timeout and loss of communication during an external switch firmware upgrade.

Click the parameter that the customer should configure within an uplink set to meet this requirement

Full Access
Question # 27

Your customer needs to move an application from an HPE Synergy 480 Gen10 Compute Module to an HPE Synergy 660 Gen 10 Compute Module. The 480 has a switch that has been manually zoned outside of HPE OneView.

What must the customer do before migrating the application?

A.

Migrate the application to a Logical JBOD and connect it to the new server

B.

Copy the server profile and assign the clone to the new hardware

C.

Edit the server profile and change server hardware type

D.

Create a new server profile template and apply to the new hardware

Full Access
Question # 28

Your customer manages HPE Synergy using HPE OneView. For one of its projects, the company purchased 50 HPE.

ProLiant DK385 Gen10 Plus v2. They plan to manage the new systems using HPE OneView as well.

What should the customer do to manage rack system using HPE OneView?

A.

add the rack system to the HPE OneView instance used to manage HPE Synergy to centralize management of all systems.

B.

connect the rack system to an IPDU and add the IPDU to the HPE. OneView instance that is used for HPE synergy management.

C.

Deploy HPE OneView Global Dashboard and add the rack systems there, as AMD systems are not directly in HPE OneView.

D.

Deploy an HPE OneView virtual appliance, and, after configuration, use it to manage only the rack systems.

Full Access
Question # 29

In the past a customer experienced a networking issue where network ports went down and came back up in quick succession.

Which HPE Virtual Connect SE 100 GD F32 Module for HPE Synergy feature can be configured to disable such ports?

A.

Pause flood protection

B.

sFlow

C.

Storm control

D.

Port flap protection

Full Access
Question # 30

Your customer plans to setup an HPE Synergy solution based on SY480 Gen10 compute nodes with the following connectivity options - SAS connectivity installed in the first fabric - FC connectivity Installed In the second fabric - Ethernet connectivity installed in the third fabric.

Which statement regarding this setup is true?

A.

Each compute node must have at least 768GB of memory installed

B.

Interconnect modules that provide SAS connectivity should be moved to the third fabric

C.

Each interconnect module in each fabric must be properly licensed in HPE OneView

D.

Compute nodes must have a second CPU installed to access the second fabric.

Full Access
Question # 31

Your customer experienced some problems caused by outdated HPE Superdome Flex firmware. Which update method should they use to avoid these issues in the future?

A.

HPE OneView method for I/O firmware update procedure

B.

RMC CLI to update I/O and HPE Persistent Memory firmware

C.

HPE OneView IT HPE Persistent Memory firmware must be updated.

D.

HPE SUM if HPE Persistent Memory firmware must be updated

Full Access