CWNA-108 Exam Dumps - Certified Wireless Network Administrator

https://www.cablinginstall.com/articles/2012/08/cat-6a-vs-cat-5e-poe.html

The statement that the lowest voltage drop is achieved when using CAT6 cable instead of Cat5 or CAT5e is true about 802.3, Clause 33 Power over Ethernet. Power over Ethernet (PoE) is a technology that allows electrical power to be delivered over Ethernet cables along with data signals. PoE is defined by IEEE 802.3, Clause 33 and has several variants, such as PoE (802.3af), PoE+ (802.3at), and PoE++ (802.3bt). PoE works by using a device called PSE (Power Sourcing Equipment) that injects power into the Ethernet cable and a device called PD (Powered Device) that receives power from the Ethernet cable. The PSE can be either an endpoint device, such as a switch or a router, or a midspan device, such as an injector or a splitter, that is inserted between two Ethernet devices. The PD can be any device that requires power, such as an access point, a camera, or a phone.

One of the factors that affects PoE performance is voltage drop, which is the reduction of voltage that occurs as current flows through a cable due to its resistance. Voltage drop can cause power loss and inefficiency in PoE systems, as well as damage to PDs if the voltage falls below their minimum requirement. To minimize voltage drop, it is recommended to use high-quality cables with low resistance and short length. Among the common types of Ethernet cables, CAT6 has the lowest resistance and therefore the lowest voltage drop compared to Cat5 or CAT5e. CAT6 also has higher bandwidth and data rate than Cat5 or CAT5e, making it more suitable for PoE applications. References: 1, Chapter 7, page 263; 2, Section 4.4

OFDM (Orthogonal Frequency Division Multiplexing) is the physical layer specification (PHY) that VHT capable devices must be backward compatible with according to the IEEE 802.11-2012 standard. VHT (Very High Throughput) is a PHY and MAC enhancement that is defined in the IEEE 802.11ac amendment and is also known as Wi-Fi 5. VHT operates only in the 5 GHz band and uses features such as wider channel bandwidths (up to 160 MHz), higher modulation schemes (up to 256-QAM), more spatial streams (up to eight), multi-user MIMO (MU-MIMO), beamforming, and VHT PHY and MAC enhancements. VHT can achieve data rates up to 6.9 Gbps.

According to the IEEE 802.11-2012 standard, VHT capable devices must be backward compatible with devices using OFDM PHY, which is defined in the IEEE 802.11a amendment and is also used by IEEE 802.11g, IEEE 802.11n, and IEEE 802.11h amendments. OFDM operates in both the 2.4 GHz and 5 GHz bands and uses features such as subcarriers, symbols, guard intervals, and OFDM PHY and MAC enhancements. OFDM can achieve data rates up to 54 Mbps.

Backward compatibility means that VHT capable devices can interoperate with OFDM devices on the same network by using common features and parameters that are supported by both PHYs. For example, VHT capable devices can use a channel bandwidth of 20 MHz, a modulation scheme of BPSK, QPSK, or 16-QAM, one spatial stream, no beamforming, and OFDM PHY and MAC headers when communicating with OFDM devices. Backward compatibility also means that VHT capable devices can fall back to OFDM mode when the signal quality or SNR is too low for VHT mode. References: 1, Chapter 3, page 123; 2, Section 3.2

What is always required to establish a high quality 2.4 GHz RF link at a distance of 3 miles (5 kilometers) is a Fresnel Zone that is at least 60% clear of obstructions. The Fresnel Zone is an elliptical-shaped area around the line-of-sight path between two antennas that reflects and refracts the RF waves. The Fresnel Zone radius depends on the frequency of the RF signal and the distance between the antennas. For optimal performance, the Fresnel Zone should be at least 60% clear of any obstructions that may cause interference, attenuation, or multipath fading. The minimum output power level, antenna gain, and antenna type may vary depending on the environmental conditions and regulatory constraints, but they are not always required for a high quality RF link. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 75; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 65.

 The data rate of a signal is the speed that the data bits in individual 802.11 data frames are sent, but it does not account for the actual amount of data that can be transmitted over time. The throughput of a connection is the flow of information over time, which is affected by various factors such as data encoding, modulation, encryption, airtime utilization, noise levels, interference, etc. Therefore, the throughput is always lower than the data rate. According to one of the web search results1, the actual throughput is normally 60-70 percent of the supported data rates. So, for a connection with a data rate of 150 Mbps, the expected throughput would be around 90-105 Mbps.

The power level at the Intentional Radiator (IR) is 250 mW. The IR is the point where the RF signal leaves the transmitter and enters the antenna system. To calculate the power level at the IR, we need to consider the output power level of the transmitter, the loss of the cable, and the gain of the antenna. The formula is:

Power level at IR (dBm) = Output power level (dBm) - Cable loss (dB) + Antenna gain (dBi)

We can convert the output power level of 50 mW to dBm by using the formula:

Power level (dBm) = 10 * log10(Power level (mW))

Therefore, 50 mW = 10 * log10(50) = 16.99 dBm

We can plug in the values into the formula:

Power level at IR (dBm) = 16.99 - 3 + 16 = 29.99 dBm

We can convert the power level at IR from dBm to mW by using the inverse formula:

Power level (mW) = 10^(Power level (dBm) / 10)

Therefore, 29.99 dBm = 10^(29.99 / 10) = 999.96 mW

However, since we need to round off the answer to the nearest integer value, we get:

Power level at IR (mW) = 1000 mW

References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 67; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 57.

The HT (802.11n) physical layer (PHY) specification includes support for and compatibility with both ERP and HR/DSSS. ERP stands for Extended Rate PHY, which is an extension of the original DSSS (Direct Sequence Spread Spectrum) PHY that supports data rates up to 54 Mbps in the 2.4 GHz band. HR/DSSS stands for High Rate/Direct Sequence Spread Spectrum, which is another extension of DSSS that supports data rates up to 11 Mbps in the 2.4 GHz band. HT stands for High Throughput, which is a new PHY that supports data rates up to 600 Mbps in both the 2.4 GHz and 5 GHz bands. HT uses OFDM (Orthogonal Frequency Division Multiplexing) as its modulation scheme, but it also supports legacy DSSS and ERP devices by using a dual preamble and header structure that allows backward compatibility. References: , Chapter 3, page 103; , Section 3.1

What prevents each station from using all the airtime when other client stations are actively communicating in the same BSS is CSMA/CA. CSMA/CA stands for Carrier Sense Multiple Access with Collision Avoidance and is a media access control method used by WLAN devices to share the wireless medium. CSMA/CA works by having each station sense the medium before transmitting a frame. If the medium is busy (i.e., another station is transmitting), the station defers its transmission until the medium is idle. If the medium is idle, the station waits for a random backoff period before transmitting. This way, CSMA/CA reduces the chances of collisions and ensures fair access to the medium for all stations. CSMA/CA also uses positive acknowledgements to confirm successful transmissions and retransmissions to recover from errors. CSMA/CD, DOS prevention, and OFDMA are not used by WLAN devices in a BSS. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 108; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 98.

The response that you should give to your manager’s suggestion of implementing the security practices of disabling the broadcasting of the SSID in Beacons and configuring the access points not to respond to Probe Request frames that have a null SSID field is that any 802.11 protocol analyzer can see the SSID in clear text in frames other than Beacons frames. This negates any security benefit of trying to hide the SSID in Beacons and Probe Response frames. The SSID (Service Set Identifier) is a human-readable name that identifies a WLAN and allows users to connect to it. The SSID is transmitted in clear text in several types of 802.11 frames, such as Beacon frames, Probe Request frames, Probe Response frames, Association Request frames, Association Response frames, Reassociation Request frames, and Reassociation Response frames. Some people may think that hiding the SSID can improve the security of the WLAN by making it invisible to potential intruders. However, this is not true, as hiding the SSID only removes it from Beacon frames and Probe Response frames that have a null SSID field. The SSID is still present in other types of frames that can be easily captured and analyzed by any 802.11 protocol analyzer or wireless scanner tool. Therefore, hiding the SSID does not provide any real security benefit and may even cause some compatibility and performance issues for legitimate users. References: 1, Chapter 4, page 133; 2, Section 4.1