CWNA-109 Exam Dumps - Certified Wireless Network Administrator

Cellular/LTE/5G is the best method for implementing a network backhaul for communications across the Internet in a remote area that is affected by a natural disaster. This is because cellular/LTE/5G networks are wireless and do not depend on physical infrastructure that may be damaged or unavailable in such scenarios. Cellular/LTE/5G networks also offer high-speed data transmission and wide coverage area, which are essential for emergency response operations. 802.11 bridging to the response team headquarters is not feasible because it requires line-of-sight and has limited range. Turning up the output power of the WLAN at the response team headquarters is not effective because it may cause interference and does not guarantee reliable connectivity. Temporary wired DSL is not practical because it requires installing cables and equipment that may not be available or accessible in a remote area. References: CWNA-109 Study Guide, Chapter 7: Wireless LAN Topologies, page 2031

Shared Key Authentication is a security solution that was defined in the original 802.11 standard as an alternative to Open System Authentication, which does not provide any security at all. Shared Key Authentication uses WEP (Wired Equivalent Privacy) to encrypt and authenticate data frames between the client station and the AP. However, WEP has been proven to be extremely vulnerable to various attacks that can easily crack the encryption key and compromise the network security. Therefore, Shared Key Authentication is deprecated in the 802.11 standard and should never be used in any modern WLAN deployment . References: [CWNA-109 Study Guide], Chapter 10: Wireless LAN Security, page 401; [CWNA-109Study Guide], Chapter 10: Wireless LAN Security, page 391; [Wikipedia], Wired Equivalent Privacy.

A 5 GHz channel should be used for this AP because channels 1 and 6 are 2.4 GHz channels and they have no impact on the decision. The 5 GHz frequency band offers more non-overlapping channels than the 2.4 GHz frequency band, which reduces interference and improves performance. The 5 GHz frequency band also supports higher data rates and wider channel bandwidths than the 2.4 GHz frequency band, which increases capacity and throughput. The 5 GHz frequency band also has less interference from other devices and sources than the 2.4 GHz frequency band, which enhances reliability and quality of service. Therefore, it is recommended to use the 5 GHz frequency band for WLANs whenever possible. Channels 1 and 6 are two of the three non-overlapping channels in the 2.4 GHz frequency band (the other one is channel 11). They are used by a neighbor network in this scenario, but they do not affect the channel selection for this AP because they operate in a different frequency band than the 5 GHz frequency band. Channel 6 is not always best to use; it depends on the interference and congestion level in the environment. Channel 1 is not best to use because it has a lower frequency than channel 6; frequency does not determine channel quality or performance. Channel 11 is not best to use because it is also a 2.4 GHz channel and it may interfere with channels 1 and 6. References: CWNA-109 Study Guide, Chapter 4: Antenna Systems and Radio Frequency (RF) Components, page 113

The device in the bridge implementation that acts as the 802.1X Authenticator is the root bridge. The root bridge is the bridge that connects to the wired network and acts as the central point for all other bridges in the point-to-multipoint topology. The root bridge authenticates the non-root bridges using 802.1X/EAP and forwards their authentication requests to the RADIUS server. The non-root bridges act as the 802.1X Supplicants and use EAP methods such as EAP-TLS or EAP-PEAP to authenticate with the root bridge. References: [CWNP Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 459; [Cisco Aironet Wireless Bridges FAQ], question 29.

https://www.wlanmall.com/what-is-a-wireless-bridge/

Wireless bridging is a WLAN technology role that allows two or more networks to be connected wirelessly over a distance. A wireless bridge consists of two or more APs that are configured to operate in bridge mode and use directional antennas to establish a point-to-point or point-to-multipoint link. Wireless bridging can support high data rates and is suitable for scenarios where running cables is impractical or expensive. To create a wireless link between two buildings on a single campus that supports at least 150 Mbps data rates, wireless bridging is an appropriate solution678. References: CWNA-109 Study Guide, Chapter 6: Wireless LAN Devices and Topologies, page 271; CWNA-109Study Guide, Chapter 6: Wireless LAN Devices and Topologies, page 265; Wi-Fi Wireless Bridging Explained.

An IEEE 802.11 amendment is a proposed change or addition to the existing 802.11 standard, which defines the specifications and protocols for wireless LANs. An amendment goes through several stages of development, such as draft, sponsor ballot, and final approval, before it is ratified by the IEEE Standards Association and becomes part of the standard. Until then, it has no official impact on the standard, although some vendors may release products based on draft amendments to gain a competitive edge or to influence the final outcome of the amendment . References: [CWNA-109 Study Guide], Chapter 1: Overview of Wireless Standards, Organizations, and Fundamentals, page 25; [CWNA-109Study Guide], Chapter 1: Overview of Wireless Standards, Organizations, and Fundamentals, page 23; [IEEE website], IEEE-SA Standards Development Process.

Patch and panel antennas are directional antenna types that are commonly used by indoor Wi-Fi devices in a MIMO multiple spatial stream implementation. These antennas have a flat rectangular shape and can be mounted on walls or ceilings to provide coverage in a specific direction. They have a moderate gain and a relatively wide beamwidth, making them suitable for multipath environments where signals can reflect off different surfaces and create multiple spatial streams. Patch and panel antennas can also support polarization diversity, which means they can transmit and receive both horizontally and vertically polarized waves, increasing the MIMO performance. References: 1, Chapter 2, page 72; 2, Section 2.4

The BSSID (Basic Service Set Identifier) is typically mapped to an AP’s MAC address if a single BSS is implemented. The BSSID is a unique identifier that distinguishes one BSS from another within the same RF medium. It is usually derived from the MAC address of the AP’s radio interface, but it can also be manually configured or randomly generated by some vendors. The BSSID is used by client stations to associate with an AP and to send and receive frames within a BSS. References: , Chapter 1, page 24; , Section 1.2