CWNA-109 Exam Dumps - Certified Wireless Network Administrator

Calibrating the floor plan is what you must do before gathering survey data after the floor plan is imported when using a site survey tool for post-implementation validation. A site survey tool is a software application that can run on a laptop, tablet, smartphone, or other device that has a Wi-Fi adapter and a GPS receiver. A site survey tool can scan the wireless environment and collect information about the detected access points and client stations, such as their SSID, BSSID, channel, signal strength, security, and data rate. A site survey tool can also measure and display various metrics of network performance, such as throughput, jitter, packet loss, delay, and SNR. A site survey tool can also use a floor plan to visualize the wireless coverage and quality in different locations on a map. A floor plan is an image file that shows the layout and dimensions of a building or an area where the WLAN is deployed. A floor plan can be imported from various sources, such as a CAD file, a PDF file, an image file, or a Google Maps screenshot. After importing a floor plan into a site survey tool, it is necessary to calibrate the floor plan before gathering survey data. Calibrating the floor plan means adjusting the scale and orientation of the floor plan to match the actual size and direction of the area. Calibrating the floor plan can be done by using a reference point or a reference line that has a known distance or angle in the real world. Calibrating the floor plan ensures that the survey data is accurate and consistent with the physical environment. References: 1, Chapter 7, page 290; 2, Section 4.3

The WLAN feature that would allow the network administrator to control the network resources that can be accessed by each employee based on their department is Role-Based Access Control (RBAC). RBAC is a method of assigning different permissions and policies to users or groups based on their roles in the organization. RBAC can be implemented by using VLANs, ACLs, or firewalls to restrict access to certain network segments or resources. RBAC can also be integrated with 802.1X/EAP authentication to dynamically assign roles and VLANs to users based on their credentials. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 403; [Role-Based Access Control (RBAC) in Wireless Networks], page 1.

 What you should tell him is that due to 802.11 network operations and the dynamic rates used by devices on the network, the two radios will likely not exceed the 1 Gbps Ethernet link. This is because the actual throughput of an 802.11 network is much lower than the theoretical data rates due to factors such as overhead, contention, interference, retransmissions, and environmental conditions. Moreover, the data rates used by devices on the network vary depending on their distance, signal quality, capabilities, and configuration. Therefore, it is unlikely that both radios of the AP will simultaneously use the maximum data rates and saturate the 1 Gbps Ethernet link. Upgrading to a 10 Gbps Ethernet link or running a second 1 Gbps Ethernet link may be unnecessary and costly. Compressing all data before transmitting it onto the Ethernet link may introduce additional overhead and latency. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 227; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 217.

An immediate concern that you note after hearing this information is that the power budget in the edge switches must be carefully planned and monitored based on the number of supported PoE devices. PoE stands for Power over Ethernet and is a technology that allows Ethernet switches to deliver power along with data to devices such as VoIP phones and 802.11 access points. PoE devices are classified into different classes based on their power consumption and output. The edge switches have a limited power budget that determines how many PoE devices they can support simultaneously. If the power budget is exceeded, some PoE devices may not receive enough power or may shut down unexpectedly. Therefore, it is important to plan and monitor the power budget in the edge switches based on the number and class of PoE devices connected to them. Using Ether-channel, placing switches in optimal locations, or avoiding distortion are not immediate concerns related to PoE devices. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 234; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 224.