H12-322 Exam Dumps - Huawei Certified ICT Professional - Wireless Local Area Network- Planning and Optimizing Enterprise WLAN

Confirm the local available channel with the customer before planning

The same channel is the same as the channel sent by the antenna connected to the AP.

Huawei's room AP6310 supports channel planning for 2.4G and 5G bands simultaneously.

Adjacent edge antennas do not use the same channel

Import Drawing -> New Project -> Set Environment -> Deploy AP -> Signal Simulation

New Project -> Import Drawing -> Set Environment -> Deploy AP -> Signal Simulation

Import Drawing -> New Project -> Deploy AP -> Set Environment -> Signal Simulation

New Project -> Import Drawing -> Deploy AP -> Set Environment -> Signal Simulation

30Mbps

90Mbps

150Mbps

300Mbps

Share-key

WPA+PSK

WPA2+802.1x

WPA2+PSK

Design

Planning

Implementation

Operation

University classroom wireless coverage

Office building wireless coverage

University dormitory wireless coverage

Hotel WOC wireless coverage

WirelessMon

inSSIDer

Omnipeek

Huawei WLAN Tester

Indoor-mounted APs are suitable for scenes with high wireless user density

Compared with indoor distributed AP, the indoor radio type AP has a large transmitting power.

Compared with indoor distributed AP, the indoor radio type AP has low transmission power

Indoor-mounted APs are suitable for scenarios with low wireless user density

TCP flow is larger than UDP flow

TCP flow is equal to UDP flow

TCP flow is smaller than UDP flow

Other options are wrong.

Using room divider antenna

Automatic packet-by-packet power control

Low speed users limit access

5G frequency band priority access

Maximize AP transmit power

Metal

Asbestos

Wooden door

Colored glass

Field strength, signal to noise ratio, signal to noise ratio

Field strength, signal to noise ratio, bandwidth

Signal to noise ratio, bandwidth, field strength

Signal to interference and noise ratio, channel, bandwidth

AP

Architectural drawings

Planning tools

Demand confirmation checklist

-45dBm

-55dBm

-65dBm

-75dBm

1234

2143

1324

2134

AP6010DN

AP5010DN

AP6010SN

AP7110DN

The transmission path of the bridge link is occluded, marking the latitude and longitude of the station.

Observe the AP and antenna installation method for the site.

Every site needs to pay attention to the location of the weak house

Whether to add a relay between the leaf site and the aggregation site

For the same drawing node, multiple, multiple tested paths can be merged

At least 2 and above paths can be merged

The path where the calculation fails occurs, and the path that failed the calculation is automatically deleted after the path is merged.

The merged path cannot be merged again

Supporting finger operations during the process of drawing obstacles, moving the scaled drawings to find the best position to draw obstacles, does not support increasing obstacle types

The industrial survey tools and planning tools need to be used together. First, get the drawings, first use the planning tools to make a simple plan for the project, and then take the Pad to the present.

Work on the site, then export the project and import it into the planning tool for further planning.

Create a new project, select the floor node, see the corresponding building thumbnail in the preview box on the right, click on the thumbnail to enter the selected floor to supplement the survey information.

Pad's industrial survey tools and planning tools are suitable for pre-sales network regulations, and WLAN test tools are used for post-production verification before delivery.

Horizontal lobes, vertical lobes

Downtilt angle

Azimuth

Gain

Ad-hoc

AP

Client

Wireless bridge

True

False

Planning

Deployment

Upgrade

Operation and maintenance

Troubleshooting

MAC certification

Portal authentication

PSK certification

Wireless 802.1x authentication

The power splitter has multiple interfaces. When signals enter from any one interface, they are equally divided into multiple signal outputs.

When the AP is at the center of the room division network, it is recommended to use a single power splitter for direct splitting.

When the AP is at one end of the room division network and the coverage area is large, it is recommended to use a coupler for signal splitting.

Power splitters and couplers cannot be used in the same network at the same time

1， 6， 11 / 6， 11， 1 / 11， 1， 6

1， 11， 6 / 6， 11， 1 / 11， 1， 6

1， 6， 11 / 6， 1， 11 / 11， 1， 6

11， 1， 6 / 1， 6， 11 / 6， 11， 1

1dBm

10dBm

20dBm

30dBm

If the leaf node needs to be used for coverage, it is necessary to pay attention to the outdoor coverage of the survey.

If there are multiple aggregation points, you need to confirm the location of each aggregation point. Each aggregation point also needs to confirm the AP installation location and power supply mode.

There should be no obstructions or distances between the convergence points and leaf nodes. There are allowed between the relay nodes and the convergence points, relay nodes and leaf points.

Obstacle obstruction

The transmission path is the path between the stations. In the site survey, it is necessary to confirm the distance between the connected nodes. The PMP mode needs to confirm the most between the links.

large angle

True

Falses

10.1.1.6/30

10.1.1.7/30

172.18.1.17/30

224.1.1.16/30

Tip shows the signal information around the point

Tip box must be placed on the heat map for 3S and above to display

The SINR and PHY Data Rate that are not displayed in the Tip box are 0.

Tip box only shows the SINR and PHY Data Rate of the maximum field strength value.

When viewing the survey, directly view the Wi-Fi signal scan box.

Reduce the current drawing scale

Before the survey, first add the AP group to speed up the simulation.

Modify the global configuration parameters to simulate the data processing granularity to the maximum value, speed up the simulation speed

True

False

1

3

6

9

Google Earth

Bitmap (jpg, gif, bmp, etc.)

PDF drawings

Vector graphics ( ai, odr, etc.)

Use the AR3260 to hang as AC

Use AC6605 to connect directly to AC

Use AC6605 to hang as AC

Use the ACU2+77 switch to do AC

When forwarding across a Layer 3 IP network, it is recommended to use centralized forwarding mode.

Only the centralized forwarding mode can be used to support roaming between different VLANs under the same aggregation gateway.

AC6005 does not support fast roaming with key caching

Roaming in the same VLAN belongs to Layer 2 roaming

10dBm

12dBm

14dBm

15dBm

True

False