NCP-MCI-6.5 Exam Dumps - Nutanix Certified Professional - Multicloud Infrastructure (NCP-MCI) v6.5 exam

The issue described pertains to the inability to ping the IPMI IPs after moving the IPMI network links to the actual switches with specific VLAN configurations. The two changes that the administrator needs to make are:

A. SSH to AHV and set the VLAN ID using IPMI Tool: Since all VLANs are tagged in the new network configuration, the IPMI network interface needs to be aware of the VLAN it’s supposed to communicate on. This can be achieved by setting the VLAN ID using the IPMI Tool on the AHV.

C. SSH to AHV and change the IP address using IPMI tool: If the IPMI IP addresses were initially set in a different subnet that is not routable in the new network configuration, the administrator would need to change the IPMI IP addresses to match the new network configuration. This can be done by SSHing to the AHV and using the IPMI Tool to change the IP address.

Enable Memory Overcommit on the over-provisioned VMs is the most efficient resolution to enable additional VMs to be created. Memory overcommit allows VMs to use more memory than physically available on a host by compressing and swapping memory pages to storage1. This can improve memory utilization and increase VM density on a cluster1. However, memory overcommit is not supported when HA is configured to use reserved hosts, so you may need to disable HA reservation on the cluster before enabling memory overcommit1.

NGT is a software package that enables advanced VM management features provided by Nutanix, such as file-level restore, VM mobility, and application-consistent snapshots12. To use NGT, you need to enable the NGT feature for a VM in the Prism Element web console, mount the NGT installer (ISO disk file) in the VM, and install NGT in the VM1. However, before installing NGT, you need to ensure that the VM can communicate with the NGT-Controller VM service, which runs on the Controller VM (CVM) of each Nutanix node3. The NGT-Controller VM service listens on port 9943 for incoming requests from the guest VMs3. Therefore, you need to enable port 9943 on the ESXi-hosted VM to allow communication with the NGT-Controller VM service.

The best method to provide access for a user to view real-time performance metrics for all VMs on all clusters across the datacenter is to configure AD authentication create a custom role, assign the user to the role, and apply the role to all clusters and VMs. This method accomplishes this with the least effort and ongoing maintenance because:

• AD authentication allows Nutanix Prism Central to integrate with an existing Active Directory (AD) domain and use AD users and groups for authentication and authorization5. This simplifies user management and avoids creating local users on Prism Central.
• Creating a custom role allows Nutanix Prism Central to define granular permissions for different actions and entities based on specific needs6. This ensures that users only have access to what they need and nothing more.
• Assigning the user to the custom role allows Nutanix Prism Central to grant access rights for that user based on the role definition7. This avoids assigning permissions individually for each user.
• Applying the role to all clusters and VMs allows Nutanix Prism Central to propagate the access rights for that role across all entities in scope8. This ensures that users can view real-time performance metrics for all VMs on all clusters without having to configure each entity separately.

References: 1: Health Dashboard - Prism Element Guide 2: Understanding Native VLANs - Cisco 3: VMs may lose network connectivity if connected to virtual network with … - Nutanix Support & Insights 4: VLAN Configuration - AHV Networking Guide 5: Active Directory Authentication - Prism Central Guide 6: Create Custom Roles - Prism Central Guide 7: Assign Roles - Prism Central Guide 8: Apply Roles - Prism Central Guide

Nutanix leverages a method for determining the bands called ‘Generalized Extreme Studentized Deviate Test’. A simple way to think about this is similar to a confidence interval where the values are between the lower and upper limits established by the algorithm.

Another web source3 shows an example of how anomaly detection works in Nutanix Prism Central. In the video, you can see that when the observed value of a metric deviates significantly from the predicted value based on historical data, an anomaly event is triggered and displayed on a chart.

Therefore, by comparing the observed values with the predicted values based on historical data, Nutanix anomaly detection can identify abnormal behavior and alert you accordingly.

According to the Nutanix Support & Insights website1, you can configure alert emails through Prism Central by enabling or disabling customer email notification for each alert. You can also modify or create custom alert policies for different entities and clusters23.

A Nutanix cluster requires a minimum of three nodes to maintain quorum and data availability. Removing a node from a 3-node cluster would violate the redundancy factor and cause data loss. Therefore, it is not possible to remove a host from a 3-node cluster using Prism or CLI. The only way to replace a node in a 3-node cluster is to use the Foundation tool, which will erase the existing cluster configuration and create a new cluster with the new node1.

The change password at next logon attribute is a setting that forces a user to change their password when they log on to a domain for the first time or after their password has expired. This attribute is enabled by default for new Active Directory user accounts or when an administrator resets a user’s password4.

However, Prism Central does not support this attribute for Active Directory authentication. Users with this attribute enabled will not be able to log on to Prism Central using their Active Directory credentials. They will receive an error message saying “Invalid credentials” or “Authentication failed” when they try to log on5.

Therefore, if an administrator is not able to log on to Prism Central using a new Active Directory user account, the most likely cause of this issue is that the change password at next logon attribute is set for that user account. To resolve this issue, the administrator should disable this attribute for the user account or log on to a domain workstation first and change their password before accessing Prism Central6.